ESCORT 3136A PDF

View and Download Escort A operation manual online. Count Multimeter. A Multimeter pdf manual download. Here you will find a large selection of new and used Escort A listed at special prices. Although some items match several categories, all of them are listed. Section 7. GPIB Remote Operation. Introduction. Description of the GPIB. GPIB Interface Parameters Setup. Commands Summary. 72 .

Author: Natilar Shakall
Country: Morocco
Language: English (Spanish)
Genre: Music
Published (Last): 10 January 2014
Pages: 335
PDF File Size: 8.61 Mb
ePub File Size: 20.83 Mb
ISBN: 224-4-61012-545-1
Downloads: 97690
Price: Free* [*Free Regsitration Required]
Uploader: Juzragore

Please refer to the chapter for related operation.

A-2 Technical Specifications Specifications assumptions: Resets the multimeter’s parameters to their default values. Select the proper function for your measurement.

The meter is acceptable only for the upper case part of command. In manual range mode, to select higher range or lower range to the desired one. Combination of Dual Display Settings Table provides the available combination of inputs for the primary display and secondary display in the dual display mode.

Selects the source of the start trigger signal. Overload Alert The meter has provided an overload alert for voltage and current measurements. Parameters may be numbers, strings or boolean. Bit set to 1 when response to query placed in output buffer. Measurement Function Selection 7.

Input Terminals Input Terminals The input terminals, shown in Figure are located on the left side of the front panel. Page 67 R1 command After executing R1 command, the meter will return the existing readings of primary display. The meter will select the appropriate range in the auto-range mode, and an annunciator on the display will indicate measurement units. OPC – Operation complete. The range setting is synchronous for dual display for current or voltage measurement. Related Manuals for Escort A No related manuals.

  GOR DIE GEGENERDE PDF

Please login or create an account. To ensure the remote interface will operate appropriately, user may need to configure the remote interface parameters by following the procedures as shown below: To avoid electric shock or injury, grounding wire in the power line cord must be connected.

Alternative equipment may be used as long as the accuracy is at least as good as those listed. Don’t show me this message again. Page 61 Table All related information for operations and functions are grouped together. Use of this instrument in a manner not specified herein may impair the protection provided by the equipment. It is unnecessary to send complete command characters.

ESCORT-3136A = FI-3136A multimeter

It 3136q only be expected to ‘ function with a Digital Multimeter. Then, any action on the device’s 31136a is enabled. Strings are case unsensitive so for instance “5m” could either be used to specify the 5mV range, or instead of “5M” for the 5 Mohm range, depending on the context. Page 32 Combination of Dual Display Settings Table provides the available combination of inputs ecort the primary display and secondary display in the dual display mode. Exceeding these limits poses a hazard to both the meter and operator.

Page 59 Table Don’t have an account? Instructions Of Command Sets If RS of the meter is under print-only mode, the meter 3163a print out the measured data when the measurement cycle is completed. Voltage, Resistance or Frequency Measurements Press the desired function button and connect the test leads as shown in Figure to measure voltage, resistance, or frequency.

  LIBRO EL PERSONALISMO DE EMMANUEL MOUNIER PDF

Commands Summary Table indicates the GPIB interface factory settings and user selectable communication parameters. Other settable ranges are: Query Commands Query Commands R0 command R0 command is used for requesting the meter to return its current status. Disconnect the live test lead before disconnecting the common test lead. This manual contains information and warns which must be followed to ensure safe operation and retain the meter in safe condition.

Recommended Test Equipment Recommended Test Equipment The test equipment requirements listed in Table or equivalents are required to perform the calibration and performance verification test procedures.

There are two types of programming commands: Page 17 Voltage, Resistance or Frequency Measurements Press the desired function button and connect the test leads as shown in Figure to measure voltage, resistance, or frequency.

Vac and frequency of the input signal you are measuring. All RS commands must be entered in the upper case.

Escort A Count Multimeter | eBay

If another positive range is specified, the nearest compatible range is set. Versions of this file set. Page 34 Table The remote control operation enables the user either to manually operate the meter via a terminal or executes a host computer program automatically.