HT12E Encoder IC can be used only with its pair HT12D. These two ICs together form an Encoder and Decoder pair. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit. Robokits India HT12E & HT12D Encoder and Decoder IC for RF Modules [RKI- ] – The HT 12E Encoder ICs are HT12E Datasheet · HT12D Datasheet.
|Published (Last):||3 April 2016|
|PDF File Size:||20.65 Mb|
|ePub File Size:||10.94 Mb|
|Price:||Free* [*Free Regsitration Required]|
If you want security you can connect any of the 8 pins to 5V to make it high. Connected to the Ground of circuit.
The 4-bit data that has to be sent has to be given to the pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. Buy 15 or more pieces to get Free Shipping Option Availability: The IC has a built in oscillator. This oscillator can ht21e used by connecting these two pins through a 1M Resistor. Customers who bought this product also purchased It is very important that your Decoder should have the same address of that of the encoder.
HT12E dahasheet a transmission enable pin which is active low. What is Web Browser. This pin has to be connected to Ground 0V to enable the Transmission.
HT12E Encoder IC
This pin powers the IC should use only 5V. These two ICs together form an Encoder and Decoder pair. This oscillator can be used by connecting these two pins through a 1M Resistor. They can also be connected to LED to physically view the received data. Arduino based GPS receiver. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.
These four pins are used to send data, the data encoded here will be decoded on HT12D IC sharing the same address bits.
HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet
Pull the Transmission Enable pin pin 14 to ground to activate transmission. Be the first to write a review. Easy Interface with and RF or an Infrared transmission medium. Photograph just for reference. HT12E begins a ht2e transmission cycle upon receipt of a transmission enable. This ICs are paired with each other.
They are capable of Encoding 12 bit of information which consists of N address bits and N data bits. The primary function of HT12E is to encode a bit and send it out through the output pin.
Transmission enable; active low. Choosing Battery for Robots.
The Encoded 12 ht2e output data obtained from HT12E has to be given here. This cycle is repeated as long as TE is kept low. It is mainly used in interfacing RF and infrared circuits. Can range from 2. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data.
We should set the bits in same pattern on Encoder and Decoder IC to pair them. These are the 8-bit address bits, which is used to protect your data.
The IC has a built in oscillator. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. Interface GPS with Arduino. HT12E is an encoder integrated circuit of 2 12 series of dataxheet. Actual product may vary from the product photograph displayed above. TB Stepper Motor Driver 4. A basic connection diagram for the HT12E IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground.
Found this item with same quality and at a lower price but prefer to buy from robokits.
They are paired with 2 12 series of decoders for use in remote control system applications. TL — Programmable Reference Voltage.
We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. It is very important that your Decoder should also have this same address for them to talk to each other. Thanks a lot for helping us to maintain competitive prices.